Genuine Polaris Surge Tank Bracket — OEM Part #5254763
Overheating can end a ride and ruin an engine. The genuine Polaris Surge Tank Bracket restores factory cooling performance on your Ranger models, with the exact fit, connections and flow the system was designed around.
The radiator, water pump, fan, thermostat, hoses and reservoir work together to hold engine temperature steady. If one part fails, the whole system suffers. This part is confirmed for 43 Polaris models from 2012 to 2023. See the full fitment list below.
Surge Tank Bracket at a Glance
-
OEM part number: 5254763
-
Brand: Polaris (genuine factory part)
-
Part type: Coolant Tanks & Components
-
Fits: Ranger utility side-by-side models, 2012–2023
-
Condition: New
Polaris Models and Years This Surge Tank Bracket Fits
Genuine Polaris part #5254763 fits the models and years below. To be certain, match the part number to the factory parts diagram for your machine or contact us with your VIN before ordering.
This part is shared across 43 Polaris model variants, so the table below groups them by model family. Your exact trim is listed in the parts diagrams linked further down.
Polaris Ranger utility side-by-side Fitment
| Model Family |
Model Years |
Trims |
| Polaris Ranger |
2015 |
1 |
| Polaris Ranger 400 |
2012–2014 |
3 |
| Polaris Ranger 500 |
2012–2013, 2017–2022 |
15 |
| Polaris Ranger 570 |
2014–2023 |
21 |
| Polaris Ranger 800 |
2013–2014 |
2 |
| Polaris Ranger ETX |
2015–2016 |
1 |
Why Choose a Genuine Polaris OEM Surge Tank Bracket?
- Factory flow and capacity for your engine
- Direct-fit connections with no adapters
- Heat- and pressure-resistant construction
- Helps prevent overheating and head gasket failure
- Sold by Witchdoctors, with factory part numbers and parts diagrams for every Polaris model we support
Features and Materials
Key Features
- Genuine Polaris OEM cooling part, part #5254763
- Original hose sizes, mounts and connectors
- Built for the pressure and temperature of the listed engines
- Designed for mud, dust and debris
- Works with factory-approved coolant
Materials and Construction
Polaris cooling parts use aluminum radiator cores, reinforced rubber hoses rated for hot coolant under pressure, glass-reinforced plastic housings and steel or stainless clamps.
Common Reasons Riders Replace This Part
- Fixing coolant leaks and overheating
- Replacing parts damaged by mud packing or debris
- Preventive replacement of aging hoses and seals
- Restoring cooling after an engine rebuild
Signs Your Surge Tank Bracket Needs Replacing
- Temperature warning or rising gauge
- Coolant leaks or a sweet smell after riding
- A fan that does not run or makes noise
- Cracked, swollen or soft hoses
- Coolant bubbling or boiling over in the reservoir
Installation Tips
- Let the engine cool completely before opening the system.
- Drain coolant into a container and dispose of it properly.
- Install the new part with fresh clamps, gaskets and O-rings where specified.
- Refill with the coolant in your Polaris manual and bleed air from the system.
- Run to operating temperature, check for leaks and top up the reservoir.
Not sure whether to tackle it yourself? Read when to seek professional help or DIY before you start.
Polaris Parts Diagrams for Your Machine
Find part #5254763 and every part installed with it in the factory Polaris parts diagrams for your model:
Related OEM Parts for the Same Machines
Doing the job right? These genuine Polaris parts fit the same models and are often replaced at the same time:
Recommended Accessories and Maintenance Supplies
Pair your Surge Tank Bracket with these parts and supplies:
Helpful Guides from the Witchdoctors Blog
Frequently Asked Questions
What is the OEM part number for this Polaris Surge Tank Bracket?
The genuine Polaris part number is 5254763. Use it to match this part to your factory parts diagram.
Which Polaris models does part #5254763 fit?
It fits 43 Polaris Ranger models from 2012 to 2023. The complete list is in the fitment tables above.
Is this a genuine Polaris part?
Yes. This is a genuine Polaris OEM part, the same part number used at the factory, not an aftermarket copy.
What coolant should I use?
Use the coolant type and mix in your Polaris owner's manual. Mixing coolant types can cause gelling or corrosion.
Do I need to bleed the cooling system?
Yes. Trapped air causes hot spots and overheating. Follow the procedure for your model.
Why does my machine overheat in mud?
Mud packed in the radiator fins blocks airflow. Clean the radiator regularly from the back side with low-pressure water.
Order Your Genuine Polaris Surge Tank Bracket Today
Get your Ranger models back to factory condition. Add the genuine Polaris Surge Tank Bracket (part #5254763) to your cart today, and order the related parts above at the same time so you can finish the job in one go.
Where to Ride Your Polaris
Ready to put your machine to work? These off-road parks welcome both ATVs and UTVs. Check each park's current rules, vehicle-width limits and permit requirements before you go.