Genuine CFMoto Bumper Cap — OEM Part #9010-040027-B000
Rocks, stumps and ledges take a toll on the underside and front end of any machine. The genuine CFMoto Bumper Cap restores factory protection on your CForce 500 or CForce 600, bolting to the original mounting points so it absorbs hits the way CFMoto engineered it to.
Bumpers, skid plates and guards are your machine's first line of defense. They spread out impacts that would otherwise bend frame rails, crack cases or damage suspension parts. This part is confirmed for 6 CFMoto models from 2010 to 2016. See the full fitment list below.
Bumper Cap at a Glance
-
OEM part number: 9010-040027-B000
-
Brand: CFMOTO (genuine factory part)
-
Part type: Front Bumper
-
Fits: CForce ATV models, 2010–2016
-
Condition: New
CFMoto Models and Years This Bumper Cap Fits
Genuine CFMoto part #9010-040027-B000 fits the models and years below. To be certain, match the part number to the factory parts diagram for your machine or contact us with your VIN before ordering.
CFMoto CForce ATV Fitment
| Model |
Model Years |
| CFMoto CForce 500 SWB |
2013–2016 |
| CFMoto CForce 500 X5 LWB |
2010–2012 |
| CFMoto CForce 500 X5 SWB |
2010–2012 |
| CFMoto CForce 600 LWB |
2013–2014 |
| CFMoto CForce 600 X6 LWB |
2010–2012 |
| CFMoto CForce 600 X6 SWB |
2010–2012 |
Why Choose a Genuine CFMoto OEM Bumper Cap?
- Bolts to factory mounting points, with no drilling
- Shields expensive components from rocks, stumps and debris
- Engineered to work with the factory frame and ground clearance
- Cheaper than repairing the parts it protects
- Sold by Witchdoctors, a CFMoto OEM parts source with factory part numbers and diagrams for every listing
Features and Materials
Key Features
- Genuine CFMoto OEM protection part, part #9010-040027-B000
- Designed around the original frame and suspension geometry
- Corrosion-resistant finish for wet and muddy conditions
- Uses factory hardware locations
- Built to take repeated trail impacts
Materials and Construction
CFMoto protection parts are typically made from steel tube, stamped steel, aluminum or high-density polyethylene (HDPE), depending on location. Each is finished to resist corrosion from mud, water and road salt.
Common Reasons Riders Replace This Part
- Rock crawling and technical trail riding
- Farm and ranch work around brush, posts and stumps
- Replacing a bent bumper or cracked skid plate after an impact
- Restoring factory protection on a used machine
Signs Your Bumper Cap Needs Replacing
- Bent, cracked or torn bumpers, plates or guards
- Missing or loose mounting hardware
- Gouges deep enough to weaken the part
- Rust-through on steel components
- Damage to the parts behind the guard
Installation Tips
- Support the machine safely on stands if you are working underneath.
- Use the CFMoto parts diagram to identify every bolt and bracket.
- Remove the damaged part and check the frame mounts for cracks or bends.
- Install the new part with fresh hardware where needed, applying thread locker if the service manual calls for it.
- Tighten to the specified torque and recheck after your first ride.
Not sure whether to tackle it yourself? Read when to seek professional help or DIY before you start.
CFMoto Parts Diagrams for This Part
Part #9010-040027-B000 appears in these factory CFMoto parts diagrams. Open the diagram for your model to see exactly where it goes and which parts are installed with it:
Other OEM Parts in This Assembly
Doing the job right? These genuine CFMoto parts are installed alongside the Bumper Cap and are often replaced at the same time:
Recommended Accessories and Maintenance Supplies
Pair your Bumper Cap with these parts and supplies:
Helpful Guides from the Witchdoctors Blog
Frequently Asked Questions
What is the OEM part number for this CFMoto Bumper Cap?
The genuine CFMoto part number is 9010-040027-B000. Use it to match this part to your factory parts diagram.
Which CFMoto models does part #9010-040027-B000 fit?
It fits the CForce 500 SWB (2013–2016); CForce 500 X5 LWB (2010–2012); CForce 500 X5 SWB (2010–2012); CForce 600 LWB (2013–2014); CForce 600 X6 LWB (2010–2012); CForce 600 X6 SWB (2010–2012).
Is this a genuine CFMoto part?
Yes. This is a genuine CFMOTO OEM part, the same part number used by CFMoto at the factory, not an aftermarket copy.
Is this as strong as an aftermarket bumper or skid plate?
It is built to CFMoto's factory standard for the listed models. Aftermarket armor may be heavier-duty, but the OEM part fits the factory mounts exactly and keeps the original weight and ground clearance.
Can I mount a winch with this part?
Only if the CFMoto parts diagram shows a winch mount for your model. Otherwise, use the dedicated winch mount listed for your machine.
Should I replace the hardware too?
Hardware that has taken a hard hit can stretch or bend. It is good practice to replace damaged bolts and use fresh thread locker.
Order Your Genuine CFMoto Bumper Cap Today
Get your CForce 500 or CForce 600 back to factory condition. Add the genuine CFMoto Bumper Cap (part #9010-040027-B000) to your cart today, and order the related parts above at the same time so you can finish the job in one go.
Where to Ride Your CFMoto
Ready to put your machine to work? These off-road parks welcome both ATVs and UTVs. Check each park's current rules, vehicle-width limits and permit requirements before you go.