Genuine Victory Drive Pulley Thin Hex Nut — OEM Part #7547311
Put the power down smoothly with a genuine Victory Drive Pulley Thin Hex Nut. Built for the Victory motorcycle, it matches the original splines, gear sizes and mounting, so it works with the rest of the driveline.
The clutch, primary, six-speed transmission, shifter, pulleys and drive belt carry every bit of engine torque to the rear wheel. This part is confirmed for 9 Victory models from 2004 to 2017.
Drive Pulley Thin Hex Nut at a Glance
-
OEM part number: 7547311
-
Brand: Victory (genuine Polaris-made OEM part)
-
Part type: Drive Pulley
-
Victory fitment: Boardwalk, Gunner, Hammer, Highball, Jackpot, Judge, Kingpin, Octane and Vegas, 2004–2017
-
Condition: New
Models and Years This Drive Pulley Thin Hex Nut Fits
Genuine part #7547311 fits the models and years below. To be certain, match the part number to the factory parts diagram for your machine or contact us with your VIN before ordering.
Victory Motorcycle Fitment
| Model |
Model Years |
| Victory Boardwalk |
2013–2015 |
| Victory Gunner |
2015–2017 |
| Victory Hammer |
2005–2017 |
| Victory Highball |
2012–2017 |
| Victory Jackpot |
2007–2016 |
| Victory Judge |
2013–2017 |
| Victory Kingpin |
2004–2012 |
| Victory Octane |
2017 |
| Victory Vegas |
2006–2017 |
Why Choose a Genuine Victory OEM Drive Pulley Thin Hex Nut?
- Exact gear, spline and bearing fit
- Restores smooth clutch engagement and shifting
- Correct belt alignment and tension
- Built for full Freedom V-twin torque
- Sold by Witchdoctors, a Victory and Indian parts specialist since the Victory years
Features and Materials
Key Features
- Genuine Victory OEM driveline part, part #7547311
- Machined to Victory's original specification
- Hardened surfaces where applicable
- Designed for the listed Victory models
- Works with factory belts, pulleys and clutch parts
Materials and Construction
Victory driveline parts use heat-treated steel gears, shafts and shift forks, friction and steel clutch plates, aluminum pulleys and covers, and carbon-fiber-reinforced drive belts.
Common Reasons Riders Replace This Part
- Fixing clutch slip or a heavy clutch pull
- Repairing missed shifts or false neutrals
- Replacing a worn or damaged belt or pulley
- Rebuilding the transmission
Signs Your Drive Pulley Thin Hex Nut Needs Replacing
- Clutch slipping under load
- Hard shifting or false neutrals
- Clunking or whining from the transmission
- Frayed, cracked or noisy drive belt
- Worn or damaged pulley teeth
Installation Tips
- Follow the Victory service manual for clutch, transmission and belt procedures.
- Replace gaskets and seals you disturb.
- Set belt tension and alignment with the correct gauge.
- Adjust clutch free play to spec.
- Test-ride gently and recheck belt tension after a few miles.
Not sure whether to tackle it yourself? Read when to seek professional help or DIY before you start.
Parts Diagrams for Your Bike
Find part #7547311 and every part installed with it in the factory parts diagrams for your model:
Related OEM Parts for the Same Bikes
Doing the job right? These genuine parts fit the same models and are often replaced at the same time:
Recommended Accessories and Maintenance Supplies
Pair your Drive Pulley Thin Hex Nut with these parts and supplies:
Helpful Guides from the Witchdoctors Blog
Frequently Asked Questions
What is the OEM part number for this Victory Drive Pulley Thin Hex Nut?
The genuine part number is 7547311. Use it to match this part to your factory parts diagram.
Which Victory motorcycles does part #7547311 fit?
It fits 9 Victory models (Boardwalk, Gunner, Hammer, Highball, Jackpot, Judge, Kingpin, Octane and Vegas) from 2004 to 2017. See the Victory fitment table above.
Does part #7547311 fit Indian motorcycles?
Not according to the factory fitment data we have. If you ride an Indian, contact us with your VIN and we will find the right part.
Is this a genuine OEM part?
Yes. This is a genuine Polaris-made OEM part, the same part number used at the factory for Victory models, not an aftermarket copy.
How do I check belt tension?
Use a belt tension gauge at the spec in your manual. Our blog covers belt checks step by step.
Should I replace both pulleys with a new belt?
Inspect the teeth. Worn or damaged pulleys will chew up a new belt.
What causes false neutrals?
Worn shift forks or detent parts, or a misadjusted shifter linkage.
Order Your Genuine Victory Drive Pulley Thin Hex Nut Today
Victory parts get harder to find every year. Order the genuine Victory Drive Pulley Thin Hex Nut, OEM part #7547311, from Witchdoctors today and keep your Victory motorcycle running the way it was built.
Where to Ride Your Victory
Put fresh parts to work on two of America's great motorcycle roads. Check road conditions, seasonal closures and park rules before you go.