Genuine CFMoto Engine Water Inlet Pipe — OEM Part #5BWV-180003-5000
Overheating can end a ride and ruin an engine. The genuine CFMoto Engine Water Inlet Pipe restores factory cooling performance on your ZForce 800 or ZForce 950, with the exact fit, connections and flow the system was designed around.
The radiator, water pump, fan, thermostat, hoses and reservoir work together to hold engine temperature steady. If one part fails, the whole system suffers. This part is confirmed for 4 CFMoto models from 2023 to 2025. See the full fitment list below.
Engine Water Inlet Pipe at a Glance
-
OEM part number: 5BWV-180003-5000
-
Brand: CFMOTO (genuine factory part)
-
Part type: Radiator Hose / Line
-
Fits: ZForce sport UTV models, 2023–2025
-
Condition: New
CFMoto Models and Years This Engine Water Inlet Pipe Fits
Genuine CFMoto part #5BWV-180003-5000 fits the models and years below. To be certain, match the part number to the factory parts diagram for your machine or contact us with your VIN before ordering.
CFMoto ZForce sport UTV Fitment
| Model |
Model Years |
| CFMoto ZForce 800 Trail |
2023–2025 |
| CFMoto ZForce 950 Sport |
2023–2025 |
| CFMoto ZForce 950 Sport 4 |
2024–2025 |
| CFMoto ZForce 950 Trail |
2023–2025 |
Why Choose a Genuine CFMoto OEM Engine Water Inlet Pipe?
- Factory flow and capacity for your engine
- Direct-fit connections with no adapters or modifications
- Heat- and pressure-resistant construction
- Helps prevent overheating, head gasket failure and warped parts
- Sold by Witchdoctors, a CFMoto OEM parts source with factory part numbers and diagrams for every listing
Features and Materials
Key Features
- Genuine CFMoto OEM cooling part, part #5BWV-180003-5000
- Matches original hose sizes, mounts and connectors
- Built for the pressure and temperature of the listed engines
- Designed for mud, dust and debris exposure
- Works with CFMoto-approved coolant
Materials and Construction
CFMoto cooling parts use aluminum radiator cores and tanks, reinforced EPDM rubber hoses rated for hot coolant under pressure, glass-reinforced plastic housings and steel or stainless clamps, all chosen to resist heat, vibration and coolant chemistry.
Common Reasons Riders Replace This Part
- Fixing coolant leaks and overheating
- Replacing parts damaged by mud packing or trail debris
- Preventive replacement of aging hoses and seals
- Restoring cooling after an engine rebuild
Signs Your Engine Water Inlet Pipe Needs Replacing
- Temperature light on or a rising temperature gauge
- Coolant leaks, drips or a sweet smell after riding
- A fan that does not turn on or makes noise
- Cracked, swollen or soft hoses
- Coolant bubbling or boiling over in the reservoir
Installation Tips
- Let the engine cool completely before opening the cooling system.
- Drain coolant into a container and dispose of it properly.
- Install the new part using fresh clamps, gaskets and O-rings where specified.
- Refill with the coolant type and mix in your CFMoto manual, and bleed air from the system.
- Run the engine to operating temperature, check for leaks and top up the reservoir.
Not sure whether to tackle it yourself? Read when to seek professional help or DIY before you start.
CFMoto Parts Diagrams for This Part
Part #5BWV-180003-5000 appears in these factory CFMoto parts diagrams. Open the diagram for your model to see exactly where it goes and which parts are installed with it:
Other OEM Parts in This Assembly
Doing the job right? These genuine CFMoto parts are installed alongside the Engine Water Inlet Pipe and are often replaced at the same time:
Recommended Accessories and Maintenance Supplies
Pair your Engine Water Inlet Pipe with these parts and supplies:
Helpful Guides from the Witchdoctors Blog
Frequently Asked Questions
What is the OEM part number for this CFMoto Engine Water Inlet Pipe?
The genuine CFMoto part number is 5BWV-180003-5000. Use it to match this part to your factory parts diagram.
Which CFMoto models does part #5BWV-180003-5000 fit?
It fits the ZForce 800 Trail (2023–2025); ZForce 950 Sport (2023–2025); ZForce 950 Sport 4 (2024–2025); ZForce 950 Trail (2023–2025).
Is this a genuine CFMoto part?
Yes. This is a genuine CFMOTO OEM part, the same part number used by CFMoto at the factory, not an aftermarket copy.
What coolant should I use?
Use the coolant type and mix ratio in your CFMoto owner's manual. Mixing coolant types can cause gelling or corrosion.
Do I need to bleed the cooling system?
Yes. Trapped air can cause hot spots and overheating. Follow the bleeding procedure for your model after any repair.
Why does my machine overheat in mud?
Mud packed in the radiator fins blocks airflow. Clean the radiator regularly with low-pressure water from the back side.
Order Your Genuine CFMoto Engine Water Inlet Pipe Today
Get your ZForce 800 or ZForce 950 back to factory condition. Add the genuine CFMoto Engine Water Inlet Pipe (part #5BWV-180003-5000) to your cart today, and order the related parts above at the same time so you can finish the job in one go.
Where to Ride Your CFMoto
Ready to put your machine to work? These off-road parks welcome both ATVs and UTVs. Check each park's current rules, vehicle-width limits and permit requirements before you go.