Genuine CFMoto Front Axle Bracket — OEM Part #7030-038110-10000
Get back on the trail with a genuine CFMoto Front Axle Bracket. Built for the UForce 500 or UForce 800, this OEM part matches the factory splines, length and bearing fit, so it installs without modification and handles full suspension travel.
Axles, CV joints, bearings and hubs carry power to the wheels while the suspension cycles through its travel. They take constant shock loads, and any wear shows up as clicking, vibration or play. This part is confirmed for 3 CFMoto models from 2013 to 2022. See the full fitment list below.
Front Axle Bracket at a Glance
-
OEM part number: 7030-038110-10000
-
Brand: CFMOTO (genuine factory part)
-
Part type: Axle Hardware
-
Position: Front
-
Fits: UForce utility UTV models, 2013–2022
-
Condition: New
CFMoto Models and Years This Front Axle Bracket Fits
Genuine CFMoto part #7030-038110-10000 fits the models and years below. To be certain, match the part number to the factory parts diagram for your machine or contact us with your VIN before ordering.
CFMoto UForce utility UTV Fitment
| Model |
Model Years |
| CFMoto UForce 500 |
2016–2020 |
| CFMoto UForce 800 |
2013–2016, 2018–2022 |
| CFMoto UForce 800 EPS |
2017 |
Why Choose a Genuine CFMoto OEM Front Axle Bracket?
- Exact spline count and length for a direct fit
- Factory CV joint angles for full suspension travel
- Designed for the torque of the listed engines
- Sealed boots and bearings to keep out water and grit
- Sold by Witchdoctors, a CFMoto OEM parts source with factory part numbers and diagrams for every listing
Features and Materials
Key Features
- Genuine CFMoto OEM axle or hub part, part #7030-038110-10000
- Matches original spline, length and bearing dimensions
- Heat-treated shafts and joints where applicable
- Boots and seals designed for mud and water
- Fits the listed CFMoto models without modification
Materials and Construction
CFMoto axles use heat-treated alloy steel shafts and CV joints packed with high-temperature grease and sealed with thermoplastic or rubber boots. Hubs and bearings use hardened steel races and seals designed for water crossings and mud.
Common Reasons Riders Replace This Part
- Replacing an axle with a clicking or broken CV joint
- Fixing torn boots before dirt ruins the joint
- Replacing worn wheel bearings and hubs
- Repairs after a hard impact or broken axle
Signs Your Front Axle Bracket Needs Replacing
- Clicking or popping when turning under power
- Torn or leaking CV boots with grease slung around the wheel
- Vibration at speed or under acceleration
- Play or grinding in the wheel bearing
- A broken axle or wheel that will not drive
Installation Tips
- Raise and support the machine safely and remove the wheel.
- Remove the axle nut. Many CFMoto axle nuts are single-use, so replace it.
- Separate the suspension as needed to remove the old axle, keeping the boot off sharp edges.
- Install the new part, making sure the splines fully seat and the circlip engages.
- Torque the axle nut and suspension hardware to spec, then reinstall the wheel and test-ride.
Not sure whether to tackle it yourself? Read when to seek professional help or DIY before you start.
CFMoto Parts Diagrams for This Part
Part #7030-038110-10000 appears in these factory CFMoto parts diagrams. Open the diagram for your model to see exactly where it goes and which parts are installed with it:
Other OEM Parts in This Assembly
Doing the job right? These genuine CFMoto parts are installed alongside the Front Axle Bracket and are often replaced at the same time:
Recommended Accessories and Maintenance Supplies
Pair your Front Axle Bracket with these parts and supplies:
Helpful Guides from the Witchdoctors Blog
Frequently Asked Questions
What is the OEM part number for this CFMoto Front Axle Bracket?
The genuine CFMoto part number is 7030-038110-10000. Use it to match this part to your factory parts diagram.
Which CFMoto models does part #7030-038110-10000 fit?
It fits the UForce 500 (2016–2020); UForce 800 (2013–2016, 2018–2022); UForce 800 EPS (2017).
Is this a genuine CFMoto part?
Yes. This is a genuine CFMOTO OEM part, the same part number used by CFMoto at the factory, not an aftermarket copy.
Do I need a new axle nut?
Many CFMoto axle nuts are designed for one use. Check the parts diagram and replace the nut and cotter pin if specified.
Can I replace just the CV boot?
If the joint is not clicking and the grease is clean, a boot kit can work. If dirt or water got in, replacing the axle is usually the better choice.
Is OEM as strong as a heavy-duty aftermarket axle?
It is built to CFMoto's factory standard for stock machines. If you run much larger tires or a lift, a heavy-duty axle may be worth considering.
Order Your Genuine CFMoto Front Axle Bracket Today
Ride with confidence on parts built for your machine. Order the genuine CFMoto Front Axle Bracket, OEM part #7030-038110-10000, from Witchdoctors today and keep your UForce 500 or UForce 800 running the way CFMoto designed it.
Where to Ride Your CFMoto
Ready to put your machine to work? These off-road parks welcome both ATVs and UTVs. Check each park's current rules, vehicle-width limits and permit requirements before you go.