Genuine CFMoto Handlebar Press Cover Bracket — OEM Part #9CR6-101204-10000
Loose, heavy or wandering steering makes every ride tiring and less safe. The genuine CFMoto Handlebar Press Cover Bracket restores precise, factory-feel steering on your CForce models, fitting the original column, rack and linkage without modification.
The steering wheel or handlebars, column, rack, tie rods and electronic power steering (EPS) all affect control. Play or binding in any one part shows up as vague or heavy steering. This part is confirmed for 6 CFMoto models from 2015 to 2025. See the full fitment list below.
Handlebar Press Cover Bracket at a Glance
-
OEM part number: 9CR6-101204-10000
-
Brand: CFMOTO (genuine factory part)
-
Part type: Handlebar Pads & Covers
-
Fits: CForce ATV models, 2015–2025
-
Condition: New
CFMoto Models and Years This Handlebar Press Cover Bracket Fits
Genuine CFMoto part #9CR6-101204-10000 fits the models and years below. To be certain, match the part number to the factory parts diagram for your machine or contact us with your VIN before ordering.
CFMoto CForce ATV Fitment
| Model |
Model Years |
| CFMoto CForce 400 |
2017 |
| CFMoto CForce 500 HO |
2015–2018 |
| CFMoto CForce 600 |
2019–2025 |
| CFMoto CForce 600 Touring |
2020–2025 |
| CFMoto CForce 800 XC |
2019–2024 |
| CFMoto CForce 1000 Overland |
2021 |
Why Choose a Genuine CFMoto OEM Handlebar Press Cover Bracket?
- Factory fit with the original rack, column and linkage
- Restores tight, precise steering feel
- Works with CFMoto EPS where equipped
- Helps keep alignment and tire wear in check
- Sold by Witchdoctors, a CFMoto OEM parts source with factory part numbers and diagrams for every listing
Features and Materials
Key Features
- Genuine CFMoto OEM steering part, part #9CR6-101204-10000
- Matches original splines, threads and joints
- Corrosion- and impact-resistant construction
- Designed for the listed CFMoto models
- Works with factory EPS units, sensors and wiring where applicable
Materials and Construction
CFMoto steering parts use hardened steel shafts, racks and tie-rod ends with sealed joints, aluminum or steel housings, and, for EPS systems, sealed motors and electronic modules designed for water and vibration.
Common Reasons Riders Replace This Part
- Fixing play, clunks or wandering
- Replacing bent tie rods or shafts after an impact
- Repairing EPS faults or a heavy steering feel
- Restoring steering on a high-hour machine
Signs Your Handlebar Press Cover Bracket Needs Replacing
- Free play or looseness in the steering
- Clunking or knocking when turning
- Heavy steering or an EPS warning light
- Bent tie rods or a steering wheel off center
- Torn boots on tie-rod ends or the rack
Installation Tips
- Point the wheels straight and lock the steering before disconnecting parts.
- Use the CFMoto parts diagram for hardware, cotter pins and EPS connectors.
- Disconnect the battery before working on EPS components.
- Install the new part, matching the original spline position or tie-rod length.
- Torque to spec, set toe, and check full lock-to-lock travel before riding.
Not sure whether to tackle it yourself? Read when to seek professional help or DIY before you start.
CFMoto Parts Diagrams for This Part
Part #9CR6-101204-10000 appears in these factory CFMoto parts diagrams. Open the diagram for your model to see exactly where it goes and which parts are installed with it:
Other OEM Parts in This Assembly
Doing the job right? These genuine CFMoto parts are installed alongside the Handlebar Press Cover Bracket and are often replaced at the same time:
Recommended Accessories and Maintenance Supplies
Pair your Handlebar Press Cover Bracket with these parts and supplies:
Helpful Guides from the Witchdoctors Blog
Frequently Asked Questions
What is the OEM part number for this CFMoto Handlebar Press Cover Bracket?
The genuine CFMoto part number is 9CR6-101204-10000. Use it to match this part to your factory parts diagram.
Which CFMoto models does part #9CR6-101204-10000 fit?
It fits the CForce 400 (2017); CForce 500 HO (2015–2018); CForce 600 (2019–2025); CForce 600 Touring (2020–2025); CForce 800 XC (2019–2024); CForce 1000 Overland (2021).
Is this a genuine CFMoto part?
Yes. This is a genuine CFMOTO OEM part, the same part number used by CFMoto at the factory, not an aftermarket copy.
Do I need an alignment after replacing steering parts?
Yes. Tie rods and steering components affect toe. Set it after installation to prevent wander and tire wear.
Does the EPS need to be calibrated?
Some CFMoto EPS systems need a reset or calibration after service. Check your service manual or ask a dealer.
Is this part safe to straighten instead of replace?
No. Bent steering parts should always be replaced. Straightened parts can fail without warning.
Order Your Genuine CFMoto Handlebar Press Cover Bracket Today
Get your CForce models back to factory condition. Add the genuine CFMoto Handlebar Press Cover Bracket (part #9CR6-101204-10000) to your cart today, and order the related parts above at the same time so you can finish the job in one go.
Where to Ride Your CFMoto
Ready to put your machine to work? These off-road parks welcome both ATVs and UTVs. Check each park's current rules, vehicle-width limits and permit requirements before you go.
-
Hollister Hills SVRA — Hollister, California: a state vehicular recreation area with designated ATV and 4x4 areas
-
Spearhead Trails — southwest Virginia: a multi-trail system across the Virginia coalfields