Genuine Can-Am Rear Knuckle, Left — OEM Part #715010183
Steer with confidence again with a genuine Can-Am Rear Knuckle, Left. Built for the Can-Am ATV or side-by-side, it matches the factory splines, joints and mounting points, so the steering feels tight and works with Dynamic Power Steering (DPS) where equipped.
The steering wheel or handlebar, column, rack, tie rods and power steering unit all affect control. Play or binding in any one part shows up as vague or heavy steering. This part is confirmed for 103 Can-Am models from 2021 to 2026. See the full fitment list below.
Rear Knuckle, Left at a Glance
-
OEM part number: 715010183
-
Brand: Can-Am by BRP (genuine factory part)
-
Part type: Steering Knuckle
-
Position: Left
-
Fits: Commander crossover side-by-side, Defender utility side-by-side, Maverick sport side-by-side and Traxter utility side-by-side models, 2021–2026
-
Condition: New
Can-Am Models and Years This Rear Knuckle Fits
Genuine Can-Am part #715010183 fits the models and years below. To be certain, match the part number to the factory parts diagram for your machine or contact us with your VIN before ordering.
This part is shared across 103 Can-Am model variants, so the table below groups them by model family. Your exact trim is listed in the parts diagrams linked further down.
Can-Am Commander crossover side-by-side Fitment
| Model Family |
Model Years |
Trims |
| Can-Am Commander 700 |
2022–2026 |
8 |
| Can-Am Commander 1000R |
2022–2026 |
8 |
Can-Am Defender utility side-by-side Fitment
| Model Family |
Model Years |
Trims |
| Can-Am Defender 6x6 |
2022–2023 |
3 |
| Can-Am Defender HD7 |
2022–2024 |
5 |
| Can-Am Defender HD9 |
2022–2024 |
9 |
| Can-Am Defender HD10 |
2022–2026 |
18 |
| Can-Am Defender PRO |
2022–2025 |
4 |
Can-Am Maverick sport side-by-side Fitment
| Model Family |
Model Years |
Trims |
| Can-Am Maverick Sport |
2021–2026 |
13 |
| Can-Am Maverick Trail |
2022–2026 |
9 |
Can-Am Traxter utility side-by-side Fitment
| Model Family |
Model Years |
Trims |
| Can-Am Traxter 6x6 |
2022–2024 |
1 |
| Can-Am Traxter HD7 |
2023–2025 |
4 |
| Can-Am Traxter HD9 |
2022–2025 |
6 |
| Can-Am Traxter HD10 |
2022–2024 |
6 |
| Can-Am Traxter PRO |
2022–2024 |
3 |
| Can-Am Traxter T |
2022 |
6 |
Why Choose a Genuine Can-Am OEM Rear Knuckle?
- Factory fit with the rack, column and linkage
- Restores tight, precise steering
- Works with Can-Am DPS where equipped
- Helps keep alignment and tire wear in check
- Sold by Witchdoctors, with factory part numbers and parts diagrams for every Can-Am model we support
Features and Materials
Key Features
- Genuine Can-Am OEM steering part, part #715010183
- Original splines, threads and joints
- Corrosion- and impact-resistant construction
- Designed for the listed Can-Am models
- Works with factory DPS units, sensors and wiring where applicable
Materials and Construction
Can-Am steering parts use hardened steel shafts, racks and tie-rod ends with sealed joints, aluminum or steel housings, and sealed DPS motors and modules built for water and vibration.
Common Reasons Riders Replace This Part
- Fixing play, clunks or wandering
- Replacing bent tie rods or shafts after an impact
- Repairing DPS faults or heavy steering
- Restoring steering on a high-hour machine
Signs Your Rear Knuckle Needs Replacing
- Free play in the steering
- Clunking when turning
- Heavy steering or a DPS warning
- Bent tie rods or an off-center wheel
- Torn boots on tie-rod ends or the rack
Installation Tips
- Point the wheels straight before disconnecting parts.
- Use the Can-Am parts diagram for hardware, cotter pins and DPS connectors.
- Disconnect the battery before working on DPS parts.
- Match the original spline position or tie-rod length.
- Torque to spec, set toe and check lock-to-lock travel.
Not sure whether to tackle it yourself? Read when to seek professional help or DIY before you start.
Can-Am Parts Diagrams for Your Machine
Find part #715010183 and every part installed with it in the factory Can-Am parts diagrams for your model:
Related OEM Parts for the Same Machines
Doing the job right? These genuine Can-Am parts fit the same models and are often replaced at the same time:
Recommended Accessories and Maintenance Supplies
Pair your Rear Knuckle with these parts and supplies:
Helpful Guides from the Witchdoctors Blog
Frequently Asked Questions
What is the OEM part number for this Can-Am Rear Knuckle?
The genuine Can-Am part number is 715010183. Use it to match this part to your factory parts diagram.
Which Can-Am models does part #715010183 fit?
It fits 103 Can-Am Commander, Defender, Maverick and Traxter models from 2021 to 2026. The complete list is in the fitment tables above.
Is this a genuine Can-Am part?
Yes. This is a genuine Can-Am OEM part from BRP, the same part number used at the factory, not an aftermarket copy.
Do I need an alignment after steering work?
Yes. Set toe to prevent wander and tire wear.
Does DPS need a reset after service?
Some systems need a reset or calibration. Check your service manual or ask a dealer.
Can a bent steering part be straightened?
No. Always replace bent steering parts.
Order Your Genuine Can-Am Rear Knuckle Today
Ride with confidence on parts built for your machine. Order the genuine Can-Am Rear Knuckle, Left, OEM part #715010183, from Witchdoctors today and keep your Can-Am ATV or side-by-side running the way BRP designed it.
Where to Ride Your Can-Am
Ready to put your machine to work? These off-road parks welcome both ATVs and UTVs. Check each park's current rules, vehicle-width limits and permit requirements before you go.