Genuine Polaris Snap Ring — OEM Part #2208329
A clicking CV joint or torn boot will leave you stranded if you ignore it. The genuine Polaris Snap Ring restores factory strength and articulation on your Polaris ATV or side-by-side, with the original spline count, length and joint angles.
Axles, CV joints, bearings and hubs carry power to the wheels while the suspension cycles. They take constant shock loads, and wear shows up as clicking, vibration or play. This part is confirmed for 175 Polaris models from 2020 to 2026. See the full fitment list below.
Snap Ring at a Glance
-
OEM part number: 2208329
-
Brand: Polaris (genuine factory part)
-
Part type: Axle Hardware
-
Fits: RZR sport side-by-side, Ranger utility side-by-side and Xpedition adventure side-by-side models, 2020–2026
-
Condition: New
Polaris Models and Years This Snap Ring Fits
Genuine Polaris part #2208329 fits the models and years below. To be certain, match the part number to the factory parts diagram for your machine or contact us with your VIN before ordering.
This part is shared across 175 Polaris model variants, so the table below groups them by model family. Your exact trim is listed in the parts diagrams linked further down.
Polaris RZR sport side-by-side Fitment
| Model Family |
Model Years |
Trims |
| Polaris RZR |
2025 |
1 |
| Polaris RZR Trctr |
2025 |
1 |
| Polaris RZR XP |
2022–2026 |
17 |
Polaris Ranger utility side-by-side Fitment
| Model Family |
Model Years |
Trims |
| Polaris Ranger |
2023 |
1 |
| Polaris Ranger 500 |
2020–2022, 2026 |
4 |
| Polaris Ranger 530 |
2023–2025 |
1 |
| Polaris Ranger 570 |
2020–2026 |
33 |
| Polaris Ranger 1000 |
2022–2026 |
44 |
| Polaris Ranger Diesel |
2023–2026 |
6 |
| Polaris Ranger EV |
2023–2024 |
7 |
| Polaris Ranger MD |
2024–2025 |
1 |
| Polaris Ranger MS |
2025–2026 |
2 |
| Polaris Ranger SP |
2026 |
1 |
| Polaris Ranger Xd |
2024–2026 |
8 |
| Polaris Ranger XP |
2021–2026 |
38 |
Polaris Xpedition adventure side-by-side Fitment
| Model Family |
Model Years |
Trims |
| Polaris Xpedition Adv |
2024–2026 |
4 |
| Polaris Xpedition XP |
2024–2026 |
4 |
| Polaris Xpedition Xp5 |
2024–2026 |
2 |
Why Choose a Genuine Polaris OEM Snap Ring?
- Exact spline count and length for a direct fit
- Factory joint angles for full suspension travel
- Designed for the torque of the listed engines
- Sealed boots and bearings to keep out water and grit
- Sold by Witchdoctors, with factory part numbers and parts diagrams for every Polaris model we support
Features and Materials
Key Features
- Genuine Polaris OEM axle or hub part, part #2208329
- Original spline, length and bearing dimensions
- Heat-treated shafts and joints where applicable
- Boots and seals designed for mud and water
- Fits the listed Polaris models without modification
Materials and Construction
Polaris axles use heat-treated alloy steel shafts and CV joints packed with high-temperature grease and sealed with durable boots. Hubs and bearings use hardened races and seals made for water crossings.
Common Reasons Riders Replace This Part
- Replacing an axle with a clicking or broken joint
- Fixing torn boots before dirt ruins the joint
- Replacing worn wheel bearings and hubs
- Repairs after a hard impact
Signs Your Snap Ring Needs Replacing
- Clicking or popping when turning under power
- Torn boots with grease slung around the wheel
- Vibration at speed or under acceleration
- Play or grinding in the wheel bearing
- A broken axle or wheel that will not drive
Installation Tips
- Raise and support the machine safely and remove the wheel.
- Remove the axle nut; replace it if it is a one-time-use nut.
- Separate the suspension as needed, keeping the boot off sharp edges.
- Install the new part, making sure the splines seat and the circlip engages.
- Torque the axle nut and suspension hardware to spec and test-ride.
Not sure whether to tackle it yourself? Read when to seek professional help or DIY before you start.
Polaris Parts Diagrams for Your Machine
Find part #2208329 and every part installed with it in the factory Polaris parts diagrams for your model:
Related OEM Parts for the Same Machines
Doing the job right? These genuine Polaris parts fit the same models and are often replaced at the same time:
Recommended Accessories and Maintenance Supplies
Pair your Snap Ring with these parts and supplies:
Helpful Guides from the Witchdoctors Blog
Frequently Asked Questions
What is the OEM part number for this Polaris Snap Ring?
The genuine Polaris part number is 2208329. Use it to match this part to your factory parts diagram.
Which Polaris models does part #2208329 fit?
It fits 175 Polaris RZR, Ranger and Xpedition models from 2020 to 2026. The complete list is in the fitment tables above.
Is this a genuine Polaris part?
Yes. This is a genuine Polaris OEM part, the same part number used at the factory, not an aftermarket copy.
Do I need a new axle nut?
Many Polaris axle nuts are single-use. Check the parts diagram and replace the nut and cotter pin if specified.
Can I replace just the CV boot?
If the joint is quiet and the grease is clean, a boot kit can work. If dirt or water got in, replace the axle.
Is OEM as strong as a heavy-duty aftermarket axle?
It is built to the factory standard for stock machines. With much larger tires or a lift, consider heavy-duty axles.
Order Your Genuine Polaris Snap Ring Today
Get your Polaris ATV or side-by-side back to factory condition. Add the genuine Polaris Snap Ring (part #2208329) to your cart today, and order the related parts above at the same time so you can finish the job in one go.
Where to Ride Your Polaris
Ready to put your machine to work? These off-road parks welcome both ATVs and UTVs. Check each park's current rules, vehicle-width limits and permit requirements before you go.