Genuine Polaris Throttle Body Adapter — OEM Part #1205301
Breathe easy with a genuine Polaris Throttle Body Adapter. Designed for the Polaris ATV or side-by-side, it fits the original airbox, ducts and clamps for a tight seal and the airflow your engine was calibrated for.
The intake path, from inlet to airbox to throttle body, has to stay sealed. One cracked boot or warped lid can let in enough dust to wear out an engine fast. This part is confirmed for 91 Polaris models from 2013 to 2023. See the full fitment list below.
Throttle Body Adapter at a Glance
-
OEM part number: 1205301
-
Brand: Polaris (genuine factory part)
-
Part type: Throttle Body
-
Fits: ACE single-seat, RZR sport side-by-side and Ranger utility side-by-side models, 2013–2023
-
Condition: New
Polaris Models and Years This Throttle Body Adapter Fits
Genuine Polaris part #1205301 fits the models and years below. To be certain, match the part number to the factory parts diagram for your machine or contact us with your VIN before ordering.
This part is shared across 91 Polaris model variants, so the table below groups them by model family. Your exact trim is listed in the parts diagrams linked further down.
Polaris ACE single-seat Fitment
| Model Family |
Model Years |
Trims |
| Polaris ACE 900 |
2016–2019 |
2 |
Polaris RZR sport side-by-side Fitment
| Model Family |
Model Years |
Trims |
| Polaris RZR 900 |
2018–2023 |
8 |
| Polaris RZR Trail |
2020, 2022 |
3 |
Polaris Ranger utility side-by-side Fitment
| Model Family |
Model Years |
Trims |
| Polaris Ranger |
2018–2019 |
2 |
| Polaris Ranger 6P |
2017 |
1 |
| Polaris Ranger 900 |
2013–2019 |
6 |
| Polaris Ranger 1000 |
2018–2019, 2021 |
5 |
| Polaris Ranger Back |
2020 |
2 |
| Polaris Ranger FC |
2020 |
2 |
| Polaris Ranger HD |
2020 |
1 |
| Polaris Ranger High |
2019–2020 |
2 |
| Polaris Ranger Is |
2020 |
1 |
| Polaris Ranger MD |
2018 |
1 |
| Polaris Ranger Northstar |
2018–2020 |
11 |
| Polaris Ranger RC |
2020 |
2 |
| Polaris Ranger Texas |
2020 |
1 |
| Polaris Ranger Tx |
2020 |
1 |
| Polaris Ranger Winter |
2020 |
2 |
| Polaris Ranger XP |
2014, 2017–2019, 2021–2022 |
38 |
Why Choose a Genuine Polaris OEM Throttle Body Adapter?
- Factory seal against dust, water and debris
- Correct airflow for the factory fuel and ignition mapping
- Direct fit with original clamps, ducts and mounts
- Helps prevent premature engine wear
- Sold by Witchdoctors, with factory part numbers and parts diagrams for every Polaris model we support
Features and Materials
Key Features
- Genuine Polaris OEM intake part, part #1205301
- Molded to original airbox and duct dimensions
- Heat- and fuel-vapor-resistant materials
- Designed for dusty, muddy and wet riding
- Works with factory air filters and sensors
Materials and Construction
Polaris intake parts use rigid, heat-stable plastics for airbox housings and lids, flexible rubber or TPE boots and ducts that seal under vibration, and filter media designed to trap fine dust while keeping airflow.
Common Reasons Riders Replace This Part
- Replacing a cracked airbox, lid or intake boot
- Restoring the seal after water or mud intrusion
- Routine filter and wear-item replacement
- Fixing idle and performance problems from an air leak
Signs Your Throttle Body Adapter Needs Replacing
- Dust on the clean side of the air filter
- Cracks or splits in boots, ducts or the airbox
- Rough idle, hesitation or a lean condition
- Whistling or sucking noises from the intake
- Water in the airbox after a crossing
Installation Tips
- Check the Polaris parts diagram for clamps, seals and duct routing.
- Remove the old part and clean dust from the airbox and throttle body inlet.
- Install the new part, making sure every edge seals.
- Tighten clamps evenly without overtightening plastic fittings.
- Start the engine and check for air leaks and a smooth idle.
Not sure whether to tackle it yourself? Read when to seek professional help or DIY before you start.
Polaris Parts Diagrams for Your Machine
Find part #1205301 and every part installed with it in the factory Polaris parts diagrams for your model:
Related OEM Parts for the Same Machines
Doing the job right? These genuine Polaris parts fit the same models and are often replaced at the same time:
Recommended Accessories and Maintenance Supplies
Pair your Throttle Body Adapter with these parts and supplies:
Helpful Guides from the Witchdoctors Blog
Frequently Asked Questions
What is the OEM part number for this Polaris Throttle Body Adapter?
The genuine Polaris part number is 1205301. Use it to match this part to your factory parts diagram.
Which Polaris models does part #1205301 fit?
It fits 91 Polaris ACE, RZR and Ranger models from 2013 to 2023. The complete list is in the fitment tables above.
Is this a genuine Polaris part?
Yes. This is a genuine Polaris OEM part, the same part number used at the factory, not an aftermarket copy.
How often should I check my air filter?
After every dusty ride if possible, and replace it at the interval in your owner's manual or sooner.
Can an intake leak damage my engine?
Yes. Unfiltered air carries fine dust that wears pistons, rings and cylinders quickly.
Will this change performance?
It restores factory airflow and sealing. If you had a leak, expect a smoother idle and better response.
Order Your Genuine Polaris Throttle Body Adapter Today
Ride with confidence on parts built for your machine. Order the genuine Polaris Throttle Body Adapter, OEM part #1205301, from Witchdoctors today and keep your Polaris ATV or side-by-side running the way Polaris designed it.
Where to Ride Your Polaris
Ready to put your machine to work? These off-road parks welcome both ATVs and UTVs. Check each park's current rules, vehicle-width limits and permit requirements before you go.