Barnett Victory Throttle Push Cable with Switch Black for Cross Country & Cross Roads & More (2010–2017) (SKU 101-85-41010)
Get smooth, light, consistent control back with the Barnett Victory Throttle Push Cable with Switch Black for Cross Country & Cross Roads & More (2010–2017) (SKU 101-85-41010).
Throttle and clutch cables connect your hands to the engine and clutch. Over time, stock cables stretch, fray, corrode inside and pick up friction, which makes the lever or throttle feel heavy, sticky or slow to return.
Barnett Victory Throttle Push Cable with Switch Black for Cross Country & Cross Roads & More (2010–2017) at a Glance
-
Brand: Barnett
-
SKU: 101-85-41010 (8 sizes)
-
Product type: Throttle Cable
-
Finish: Black
-
Sizes: Stock, Plus 2", Plus 3", Plus 4", Plus 6", Plus 8", Plus 10", Plus 11"
-
Fits: Victory Cross Country & Cross Roads & More (2010–2017); 4 models listed below
How Barnett Cables Are Built
-
Low-friction nylon/Teflon inner liner for smooth movement and minimal drag.
-
Heat-treated, lubricated inner wire for strength and consistent feel over time.
-
Choice of housing finishes to match the look of your bike.
-
Made for the listed models with the correct ends and routing.
Throttle Pull, Push and Idle Cables Explained
Most V-twins use two throttle cables. The pull (opening) cable opens the throttle when you twist the grip. The push or idle (closing) cable helps close it and is a key safety part. Bikes with cruise control may need a specific push cable. Replace both at the same time for even feel.
Cable Care and Lifespan
A good cable should feel smooth and return instantly for years. To keep it that way, route it without tight bends, keep it away from exhaust heat, and check the ends for fraying at every service. Adjust free play as the cable seats in during the first few hundred miles. If the lever or throttle starts to feel notchy or heavy again, inspect the routing first; a pinched or kinked housing is the most common cause of a heavy pull. Replace any cable with broken strands right away, because a frayed throttle or clutch cable can fail without warning.
Choose Your Housing Finish
-
Black (this cable): durable, UV-resistant and close to the factory look, with Barnett's smoother internals.
-
Stainless Steel: corrosion- and UV-resistant with a custom look. The clear coat helps protect surfaces the cable touches and is guaranteed not to yellow with age.
-
Stealth Black: black vinyl over stainless steel braid for a subtle, aggressive look that blends with dark finishes.
-
Platinum Series: clear-coat protective finish with chrome or polished hardware and elbows where applicable. The clear coat helps protect painted surfaces and is guaranteed not to discolor from sun exposure.
Choosing the Right Length
This cable comes in 8 lengths: Stock, Plus 2", Plus 3", Plus 4", Plus 6", Plus 8", Plus 10", Plus 11". Choose Stock for stock handlebars. If you have taller bars, risers or pullback bars, measure how much longer your setup is than stock and choose the matching "Plus" length.
- Measure the stock routing from the control to the end point with a string, then measure your new routing the same way.
- The difference is the extra length you need.
- When in doubt, contact us with your bar or riser brand and size.
Read our guide on how to measure motorcycle handlebars for more help.
Signs It's Time to Replace
- Stiff or heavy lever or throttle pull
- Lever or throttle that sticks or returns slowly
- Frayed ends or kinked housing
- Delayed or inconsistent response
Fitment
The Barnett Victory Throttle Push Cable with Switch Black for Cross Country & Cross Roads & More (2010–2017) is listed for the models below. Confirm your model and year, or contact us with your VIN before ordering.
| Model |
Model Years |
| Victory Cross Country |
2010–2017 |
| Victory Cross Country Tour |
2012–2017 |
| Victory Cross Roads |
2010–2014 |
| Victory Hard-Ball |
2012–2013 |
Why Choose Barnett?
- Smoother, lighter lever and throttle feel
- Consistent action that lasts
- Custom housing finishes
- Made for the listed models
Barnett has made control cables and clutch components for decades, and riders choose Barnett for smooth operation, durable materials and custom finishes. Witchdoctors stocks Barnett cables and clutches for Victory and Indian motorcycles, plus off-road clutch parts.
Who It's For
- Replacing worn or frayed stock cables
- Handlebar or riser changes that need longer cables
- Matching cable finish to a custom build
- Preventive replacement before a long trip
Installation Overview
- Choose the right length: Stock, or longer to match taller bars or risers.
- Note the routing of the old cable, and take photos.
- Remove the old cable following your service manual.
- Install the Barnett cable along the same routing, away from heat and sharp edges, and set free play to spec.
- Turn the bars lock to lock with the engine idling. The idle must not rise, and the throttle must snap closed on its own.
Throttle, clutch and brake parts affect safety. Follow the included instructions and your service manual, and read when to seek professional help or DIY if you are unsure.
Tips from the Witchdoctors Garage
- Route cables before tightening anything.
- Use zip ties loosely so cables can move with the bars.
- Check free play after the first ride.
- Replace clutch and throttle cables together for a matched look.
More Barnett Control Cables for Victory Cross Country & Cross Roads & More
Complete the Job
Helpful Guides from the Witchdoctors Blog
Frequently Asked Questions
What is the Barnett part number?
The SKU is 101-85-41010. Use it to match the exact part you need.
Is this genuine Barnett?
Yes. Witchdoctors sells genuine Barnett products.
Which length do I need?
Stock fits stock bars. If you changed bars or risers, measure the extra height and choose the matching length. Our handlebar measuring guide explains how.
Should I replace both throttle cables?
Yes. Replacing the pull and push cables together gives the best feel.
Do Barnett cables need lubrication?
Barnett uses a lubricated wire and low-friction liner. Follow the instructions included with the cable.
Will the idle rise when I turn the bars?
It should not. If it does, the cable is too short or misrouted; correct it before riding.
How fast does Witchdoctors ship?
See how long it will take to receive your order for current timing.
Order Your Barnett Victory Throttle Push Cable with Switch Black for Cross Country & Cross Roads & More (2010–2017) Today
Ride with smoother, more confident control. Order the Barnett Victory Throttle Push Cable with Switch Black for Cross Country & Cross Roads & More (2010–2017) from Witchdoctors today.
Where to Ride Your Motorcycle
Fresh controls, open road. These scenic routes are favorites with motorcycle riders. Check current rules, road conditions and permit requirements before you go.